Results 1 to 7 of 7

Thread: Needed: Duratec crankshaft pulley holder

  1. #1
    Join Date
    Oct 2014
    Posts
    102

    Default Needed: Duratec crankshaft pulley holder

    Unfortunately, I need to get the front cover off of my Duratec without removing it from the car. In order to do this, I need the Ford service tool #205-126 ( or an effective facsimile). It holds the pulley in place while you remove the crankshaft pulley retaining bolt with an impact gun.

    I'll spare you my tale of woe...



    TIA
    Last edited by Papak; September 28th, 2016 at 03:29 PM.

  2. #2
    Join Date
    Sep 2003
    Location
    Newbury Park, CA
    Posts
    2,245

    Default

    You will also need the pin to properly align the crankshaft to TDC when you put it back in.

    I don't have either but please do not use the pin to hold the crank in place while you install the NEW crankshaft pulley bolt.

    Where are you located? You might be able to make your own.

  3. #3
    Join Date
    Oct 2014
    Posts
    102

    Default

    Doug,

    I have the pin, etc. when I first installed it, the engine was on the stand and a flywheel lock was in place. In order to do this in the car, this bar is needed. I'll probably order it today. The cost of fabrication is almost as much as the purchase price when I cost out my time and mileage. Thanks

  4. #4
    Join Date
    Sep 2003
    Location
    Newbury Park, CA
    Posts
    2,245

    Default

    When you get one, we can list it on the Resources page and you might be able to sell or rent it to another member. It will help defray the cost.

    The resources page is listed on our home page. www.californiacaterhamclub.com

  5. #5
    Join Date
    Oct 2014
    Posts
    102

    Default

    I will do that, no charge, of course. It should be here on Monday but I I be waiting a few days more for a new pulley. The rubber layer on mine is frays and torn. Might as well do it now.

  6. #6
    Join Date
    Sep 2003
    Location
    Newbury Park, CA
    Posts
    2,245

    Default

    Did you order the new crankshaft bolt as well? They are one time use.

  7. #7
    Join Date
    Oct 2014
    Posts
    102

    Default

    Yes, washer as well.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Upholstery shop needed
    By Papak in forum Questions and Answers
    Replies: 0
    Last Post: December 7th, 2015, 12:54 PM
  2. Are you close to Portland? Favour needed.
    By Dikko in forum Idle talk
    Replies: 4
    Last Post: August 16th, 2011, 01:28 PM
  3. Underdrive pulley question??
    By Roll a 7 in forum Questions and Answers
    Replies: 5
    Last Post: April 19th, 2007, 08:14 PM
  4. Info needed thinkingof getting one..
    By 02barebones996 in forum Questions and Answers
    Replies: 2
    Last Post: September 13th, 2006, 08:44 PM
  5. Headrest tube needed
    By Capt. Molecule in forum Questions and Answers
    Replies: 1
    Last Post: June 28th, 2005, 12:27 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •